Home > PLUMBING > ROUGH PLUMBING SUPPLIES > PUMPS (NON-WELL) > MACERATING PUMPS
Sort By:
Page of 1
EXT PIPE SANIFLO WHT 18IN PVC PUMP DRAIN WATER HEAVY DUTY PUMP MACERATING WHT 3/4IN/1IN
SFA Saniflo introduced this accessory in order to ease the installation as this new addition made it simpler to hide the pump behind any finished wall. This Extension Pipe is used with the Saniaccess 2, Saniaccess 3, Saniplus and Sanibest Pro external macerators. The 18 extension pipe was designed with the idea to reduce time when installing our macerators. It has an inner gasket which connects to the rear spigot of the toilet without any difficulty. Its sealed connection keeps water from seeping out once the toilet is flushed. Its ease of installation is the reason why installers recommend this accessory for any Saniflo installation. When using the extension pipe, the toilet bowl should be raised 3/8 in for additional gravity flow toward the macerator box. The Sanivite drain pump is used to pump gray water away from a variety of fixtures in commercial and residential applications. The system is able to discharge the waste up to 16 ft vertical and/or 150 ft horizontal. This model is small enough to fit inside a kitchen cabinet and was designed to sustain the toughest applications as it is capable of handling hot water and grease. The Sanivite model was designed to sustain the toughest applications meant for drain pumps. Its pumping capabilities and unique design are the reason why these range of pumps are preferred for heavy duty applications. The inside of the Sanivite is comprised of a pressure chamber, which starts and stops the unit and the motor, which drives the pump. When the water enters the Sanivite, it activates a micro switch in the pressure chamber, which in turn starts the motor. The motor is sealed for life in an oil filled enclosure. A spindle/shaft drives the impeller and therefore the moving parts are kept to an absolute minimum. Water enters the chamber and is pumped away into the sanitary sewer. The unit pumps the effluent upward to 16 ft and/or 150 ft horizontally (with gravity fall). Once the water is discharged and the water level in the container goes down, the micro switch deactivates the unit until water enters the unit again. A normal operating cycle for the Sanivite can be as short as 2 to 10 sec depending upon the discharge pipe run configuration power consumption is therefore minimal. In addition to a sink, the Sanivite will also accept and discharge the waste water from a variety of other sanitary fixtures such as: a shower, a bathtub, a urinal and a whirlpool. When adding a bathtub or shower, a base will have to be constructed. This base should be made out of a 2 x 6 (minimum) or 2 x 8 (recommended) on edge, to allow for the installation of a P-trap and the required 1/4 per foot gravity flow towards the pump unit. The Sanivite can also accept gray water from a washing machine through an indirect connection such as a laundry sink. The waste water from other sanitary fixtures is discharged into the Sanivite via two 2 in inlets, on either side of the housing and an additional 1-1/2 in inlet on the top of the unit. The discharge elbow on top of the Sanivite can be turned either to the left, to the right or towards the back, depending on the discharge installation. A non-return valve, which comes already assembled on the discharge elbow, prevents back flow into the unit. This unit has been designed with a vent connection on the lid. All plumbing codes require connection to a vent system. Please note that the vent system should be a two-way air vent. The use of mechanical vents, air admittance valves or similar devices are not permitted as these are considered one-way air vent systems. It is also highly recommended for the drain pump to be connected to a Ground Fault Interrupter (GFI) circuit. The Sanivite is small enough to fit comfortably inside a kitchen cabinet or vanity or inside the overhang of a whirlpool. The Saniplus is a 1/2 hp pump system used to install a complete bathroom up to 15 ft below the sewer line or even up to 150 ft away from a soil stack. It incorporates a macerating system which can handle human waste and toilet paper in residential applications. The blade is made out of a hardened stainless steel material which eliminates the need for any service or replacement. The inside of the Saniplus comprises of a pressure chamber, which starts and stops the unit and the motor, which drives the stainless steel macerator blades and the pump. When the flush is activated, the water flowing into the Saniplus activates a micro switch in the pressure chamber, which in turn starts the motor. The motor is sealed for life in an oil filled enclosure. A common spindle/shaft drives the impeller and the macerator blades. The moving parts therefore are kept to an absolute minimum. Water and organic waste matter enter the chamber and are reduced to slurry as the macerator blades rotate at 3600 rpm. The centrifugal force causes the reduced solids to be ejected through a grill into the container where it is picked up by the impeller pump mounted beneath the motor. The unit pumps the effluent upward to 15 ft and/or 150 ft horizontally (with gravity fall). Once the water level in the container goes down, the micro switch deactivates the unit until the flush is activated again. A normal operating cycle for Saniplus takes about 10 to 12 s depending upon the discharge pipe run configuration power consumption is therefore minimal. In addition to the toilet waste, the Saniplus will also discharge gray water from a variety of other sanitary fixtures such as: a sink, a bathtub, a shower and a urinal. When adding a bathtub or shower, a base will have to be constructed. This base should be made out of a 2 x 6 in (minimum) or 2 x 8 in (recommended) on edge, to allow for the installation of a P-trap and the required 1/4 in per foot gravity flow towards the pump unit. The wastewater from other sanitary fixtures is discharged into the Saniplus via two 2 in inlets on either side of the housing. Either one or both inlets can be used as required. The discharge elbow on top of the Saniplus can be turned either to the left, to the right or towards the back, depending on the discharge installation. A non-return valve, which comes already assembled on the discharge elbow, prevents back flow into the unit. This unit has been designed with a vent connection on the lid. All plumbing codes require connection to a vent system. Please note that the vent system should be a two-way air vent. The use of mechanical vents, air admittance valves or similar devices are not permitted as these are considered one-way air vent systems. It is also highly recommended for the macerator/pump to be connected to a Ground Fault Interrupter (GFI) circuit. The design of this model consists of vibration absorbers which enable the reduction of operating sound by reducing the transmitted sounds from any location where such resonance transmission could occur. This new design reduces the operating sound of this pump by 10 dB. The Saniplus unit must be connected to our rear discharge toilet. This system uses much less water than a regular toilet.
TRASH/SEWAGE PUMP WHITE 120V PMP GRNDR WHT 4.8LPF3/4-1"
Saniflo Up-Flush Toilet and Macerator, 115 V, 0.3 hp, 1.28 gpf, White, Porcelain, Floor Mounting The Sanibest Pro is a 1 hp pump system used to install a complete bathroom up to 25 ft below the sewer line or even up to 150 ft away from a soil stack. It incorporates a grinder system which is ideal for uncontrolled environments in both residential and commercial applications (i.e. rental unit, offices and warehouses). The Sanibest Pro is designed to handle sanitary products that may have been flushed down the toilet, such may consist of condoms, sanitary napkins, Q-tips and dental floss.