Home > PLUMBING > ROUGH PLUMBING SUPPLIES > WATER HEATER PARTS & ACCESSORI > PRESSURE RELIEF VALVES
Sort By:
Page of 1
VALVE RELIEF T/P NCLX-5 3/4IN VLV RLF TEMP/PRESS 3/4IN BRZ VLV RLF TEMP/PRESS 3/4IN BRZ
Cash Acme Pressure Relief Valve, Nominal Size: 3/4 in Watts Temperature and Pressure Relief Valve, Nominal Size: 3/4 in, NPT Connection, Operating Pressure: 125 psi, Body Material: Bronze Watts Temperature and Pressure Relief Valve, Nominal Size: 3/4 in, NPT Connection, Operating Pressure: 150 psi, Body Material: Bronze, Dimensions: 1-3/4 in L x 3-1/2 in W x 1-1/8 in H, Suitable for: Water Heaters up to 105,000 BTU/hr
VALVE RELIEF T/P NCLX-5LX 3/4 VLV VAC RLF BRZ 1/2IN DIA VLV RLF TEMP/PRESS 3/8IN BRZ
Reliance Worldwide NCLX Temperature and Pressure Relief Valve, Nominal Size: 3/4 in, MNPT x FNPT Connection, Operating Pressure: 150 psi, Actuator Type: Lever, Body Material: Bronze, Temperature Rating: 210 deg F Series N36 water service vacuum relief valves are used in water heater/tank applications to automatically allow air to enter into the piping system to prevent vacuum conditions that could siphon the water from the system and damage water heater/tank equipment. They have a brass body construction with NPT male inlet connection and a protective cap. Series N36 has a low profile design, is tested and rated to ANSI Z21.22 and is CSA certified. It is suitable for low pressure steam and water service and is ideal for use in domestic water heaters and supply tanks, table top heaters, jacketed steam kettles, unit heaters, low pressure steam systems and steam coil heaters. Watts Temperature and Pressure Relief Valve, Nominal Size: 3/8 in, Body Material: Bronze, Dimensions: 12-7/8 in L x 7-1/2 in W x 8-7/8 in H, Suitable for: Water Heaters up to 100,000 BTU/hr
VLV PRESS RLF ADJ 3/4IN BRZ VLV RLF TEMP/PRESS 3/4IN BRZ VALVE TEMP/PRESS RELIEF 3/4IN
Series 3L pressure relief valves are used in residential applications to protect against excessive pressure on domestic storage tanks, tankless water heaters and solar heating applications. They have a bronze body construction with NPT threaded male inlet and NPT threaded female (drain) outlet connections, stainless steel spring and test lever. Model 3L-Z9 has a stainless steel lever and pin for outside solar applications. ANSI Z21.22 approved, ASME rated and design certified and listed by CSA. Can be used with Watts Series 210 gas shutoff valve. Watts Temperature and Pressure Relief Valve, Nominal Size: 3/4 in, Male x Female Connection, Body Material: Bronze, Dimensions: 3-1/2 in H x 1-7/8 in W, Temperature Rating: 210 deg F Used in water heater and hot water storage tank applications to provide automatic temperature and pressure protection to hot water supply tanks and hot water heaters up to 105,000 Btu/hr. It features an extended shank for installation on water heaters with extra thick insulation as well as a bronze body with NPT male inlet and NPT female outlet connections, unique thermostat with special thermo-bonded coating and a test lever. It is suitable for water heaters with up to 2 in (50.8 mm) of insulation. It is ASME rated and CSA listed. The temperature relief is 210 deg F (99 deg C), the pressure relief range is 75 to 150 psi (5.2 to 10.3 BARs) and the standard pressure setting is 150 psi (10.55 BAR).
VLV PRESS RLF TEMP BRZ 3/4IN Camco Mfg 10473 Pressure Relief Valve 3/4 In Camco 10493 Temperature and Pressure Relief Valves
Watts Pressure Relief Valve, Nominal Size: 3/4 in, Body Material: Bronze Camco USA's 3/4 in temperature and pressure valve with 4 in probe will help protect your RV or home water heater from excessive temperature and water pressure. It's factory set at 150 psi and 210 deg F. It features epoxy-coated probe to prevent corrosion buildup. Setting: of 150 psi/210 deg F, stainless steel spring, all brass body, ANS Z21.22 design, AGA certified, epoxy coated extension probe.
VALVE T/P 3/4IN 3-5/16LS150PSI
The Camco USA T and P relief valve safely relieves excess temperature and pressure in your water heater. The Camco USA T and P valve is safe for use up to 150 psi and/or to 210 deg F. It has a 3/4 in inlet or outlet and a 3-5/16 in long shank. Durable all copper alloy body.